Primer concentrate CERAfix® 102
Tile undercoat concentrate CERAfix 102
PRIM-CONCENTRATE-(CERAFIX 102)-1LTR
CERAFIX
Register now and access more than 125,000 products
Reduces surface absorbency
- Surfaces sensitive to moisture are protected
- Extends the tile adhesive drying time
Good adhesive bond
Increases the adhesive strength of tiles and other coverings.
Depth action
Solidifying effect
Low consumption
- Very economical surface preparation
- Reduces costs
White-coloured formula is transparent once dry
Can also be used under coloured paints or for pre-treating natural stones
Quick drying time
- Quick to build up layers (e.g. with subsequent sealing and laying work)
- Reduces downtimes
Water- and alkali-resistant
Suitable for indoor and outdoor use and for surfaces exposed to water
Low-odour
Solvent-free
Higher temperatures and low relative humidity accelerate the film formation time; lower temperatures and higher relative humidity extend the film formation time.
Datasheets(X)
CERAfix 102 is used to prime absorbent and slightly sandy surfaces made from cement and gypsum materials, concrete, plaster, gypsum plasterboard, masonry etc. CERAfix 102 improves adhesion, bonds builder's dust and has a solidifying effect on the surface. CERAfix 102 is reliable at reducing surface absorbency, thereby preventing extraction of water from the fillers and tile adhesives. CERAfix 102 is used as an adhesion promoter for seals, filler and compensating compounds and for tile adhesives and emulsion paints in indoor and outdoor applications.
Depending on the surface properties, area of application and absorbency, can be diluted with water from 1:3 to 1:6. With a mixing ratio of 1:3, the treated surface is slightly solidified and significantly reduces absorbency. A mixing ratio of 1:6 binds dust. Apply CERAfix 102 with a universal or paste brush, construction or ceiling roller or a suitable spraying device. Puddling or oversaturation of the surface must be prevented during application. When CERAfix 102 is applied by spraying, roll or brush it again when freshly laid. Allow CERAfix 102 to dry fully before proceeding with additional steps.
When using with CERAfix 201, CERAfix 202, CERAfix 301 or CERAfix 302 products, a mixing ratio of 1:3 must be used.
Surface:
The surface must be solid, load-bearing, clean, dry and free from separating substances. Separating materials or layers such as layers of sinter, dust, oil, rubber abrasion, paints etc. must be removed with suitable measures such as blasting, milling, sanding, suction and/or removal of oil. The surface must have sufficient load-bearing capacity for the active loads – refer to DIN 1055. The requirements regarding surface tensile strength are in line with the intended purpose. Observe the prescribed residual moistures for subsequent coverings. When doing so, ensure that the permitted residual moisture content is observed in accordance with current technical leaflets. The CM measurement must be conducted in accordance with the current work instruction "Interface coordination for heated floor constructions". Subsequent moisture ingress must be prevented. During application and in the week after, the air, material and surface temperature must not exceed +5°C.
Colour | White |
Mixing ratio | 1:3 - 1:6 |
Contents | 1 l |
Viscosity/consistency | Thin fluid |
Can be covered after max. | 16 h |
Drying time | 3 h |
Conditions for drying time | at 20°C and 65% relative humidity |
May be walked on after max. | 3 h |
May be walked on in following conditions | at 23°C and 50% relative humidity |
Conditions for full resilience | at 23°C and 50% relative humidity |
Min./max. processing temperature | 5 to 30 °C |
Resistance against | Alkali, Water |
Solvent-free | Yes |
Min/max. application quantity in weight/area | 30-80 g/m² |
Min. application quantity in weight/area | 30 g/m² |
Max. application quantity in weight/area | 80 g/m² |
Container | Plastic bottle |
Shelf life from production | 15 Month |
Conditions to maintain shelf life from production | cool and dry storage area, 5°C to 25°C |
Select RAL-colour code
!! NOTE: On-screen visualisation of the colour differs from real colour shade!!